Use conventional carpentry tools including fine toothed saws. Power tools may be run at speeds appropriate for timber. Nail and screw holes do not require pre-drilling. Off-Cuts Kayflow unveils latest machinery investment to aid product development and reduce energy consumption You're able to select a preferreddelivery date in your shopping basket. Whilst we aim to deliver your items on this date, it is not guaranteed.

Unfortunately, not many people are familiar with these terms, so we thought you might appreciate a few words of explanation. Barge board is the name given to the Board that runs up each side of a gable or apex, forming the top two sides of a triangle. It looks the same as a Fascia Board and indeed the same board can be used, although a Barge board does not carry out any supporting structural function on the roof. When replacing old fascias and barge boards you shouldn't assume that they will be the same size - the bargeboard very is often smaller than the fascia. BARGE BOARD There are various terms used to describe Fascia Boards. It is important to understand what type of fascia is fixed to your roof, as it does have a bearing on the type of fixings you use for your gutters. The explanations below should enable you to decide exactly how to fix your gutters to your fascias. What exactly is a Fascia Board? Manufacturer guarantees are based on technical testing information obtained from BSI and are valid on the basis that manufacturers recommendations for installation are followed.Always leave a minimum 4mm expansion gap at the end of each board, ie where two boards meet leave 8mm overall. Sealants Contractors for new build and refurbishment works should be aware that larger off-cuts from some boards may have been scheduled for use in other areas of the installation and should be handled carefully until their use is established. Fascia Boards Compliance with these ventilation standards is required on all buildings, except those that were constructed without ventilation provision or predate the Buildings Regulations. However we recommend that adequate ventilation is provided on all refurbishment projects regardless of age. Sequence of Work Edge Building Products A4 grade stainless steel plastic headed nails or capped screws. See below table. Product Box ends have to account for the various angles on an individual roof’s gable end, meaning they need to be precisely installed. For anyone involved in box end construction, we’ve created a step-by-step guide that details the process.

Replacement ogee fascia boards with a more decorative finish compared to our standard fascia board. Ideal for new build and refurbishment projects, this distinctive sculptured finish will make an attractive improvement to any home. Choose our standard fascia board for a more traditional finish. The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias. B. Measure and cut box end from a deep board. Front edge should tilt up to match height of fascia board.The box end construction for fascias, soffits and gutters is located on the corners of a property’s gable end. Its purpose is to connect fascias and soffits on the non-gable end to the bargeboards that are situated at the gable end. This gives the corners of the roofline a neat finish. Our UPVC products are designed to reduce the need for maintenance to the minimum. We recommend washing your UPVC fascia boards with non-scratch sponges, mild detergent and water. The UPVC fascia and soffits are resilient to most acids but could be damaged by solvents. We don’t recommend painting foam profiles unless done by an approved contractor. Please note that creosote and bitumen-based products could cause staining of the profiles. As box end construction is a highly technical job, we supply and fit all the materials required for it. This includes high-quality uPVC fascias and soffits, uPVC and aluminium gutters.

This is no mean feat, especially when it is raining hard. In a downpour the roof of a 3-bed semi could be washing several gallons of water per second into its gutters. What configurations for guttering and downpipes are there? Step 1: Fitting the fascia board so it’s level There is usually a lip or a rebate on the bottom edge of the fascia board to support the front edge of the soffit. DURING CONSTRUCTIONOur fascia profiles come wrapped in polythene sleeves with a particular shade of white. We recommend that the protective tape is removed just before installation to avoid damage to the product.