Sovol SV01 Pro 3D Printer with Metal Direct Drive Extruder, CR Touch Auto Bed Levelling Sensor, 32-bit Silent Motherboard TMC2208 and Flexible Magnetic Bed, Printing Size 280 x 240 x 300 mm

Product Information

If the filament can be put into the extruder but no extrusion, please check if the filament stucks in the extruder or something else stucks in the or has clog issue, if you it has clog issue, please watch this video to clean the hot end and the nozzle. The smooth aluminum extrusions of the Sovol SV01 Pro make the printer look nicer, and the base is similar to what you get on the SV04.

SOVOL 3D Printer - Official Website, Leading 3D Printer SOVOL 3D Printer - Official Website, Leading 3D Printer

I have even drag on a piece of paper all over the print bed, which is glass with a textured surface - looks very much like Anycubic Ultrabase. Please make sure you press this exrtuder clip out when you load the filament and pre-heat the nozzle to 180°. Dual Z-axis screws and stepper motors improve the accuracy and precision of the nozzle's vertical movement with a specified Z-axis accuracy of 0. You should check where has the leakage, if it just happens between the nozzle and the heat sink, you just need to clean the nozzle( heat the nozzle to 200 °， and use the tool to clean it, then tighten the nozzle, or replace a new nozzle. The SV06 flexible PEI-coated build plate with mesh surface design makes the prints can be removed easily without any tools.The bottom side of the duct is really close to the print, and because of that, I had four failed prints during the review period. Reduce the speed to 10-15mm/s for printing TPU (Using a PC sticker side is recommended), and it is recommended to add Brim or place the printer into the insulation cover to print high-temperature filaments such as ABS. It felt like it was grinding on something sharp inside the filament sensor housing and didn’t pass through easily. Besides your regular controls, you get access to advanced settings like PID tuning, Acceleration and Jerk, Steps, and even Linear Advance value. Sovol double-sided flexible plate is combined with 2 parts, a flexible steel plate coated with PEI textured surface on one side, a build surface sticker on the other side, and a magnetic bottom plate with adhesive on the back.

SOVOL SV01 MANUAL BOOK Pdf Download | ManualsLib SOVOL SV01 MANUAL BOOK Pdf Download | ManualsLib

Whether you use Marlin firmware as the driver for your open or closed-source product, you must keep Marlin open, and you must provide your compatible Marlin source code to end users upon request. The SV01 comes with the Meanwell power supply, the 40×40 aluminum extrusion on the Y, as well as further extrusions across the printer to increase the stability of the printer. Install Ocotprint plugins "Action Commands", "Action Command Notification Support" and "Action Command Prompt Support".I didn’t have the chance to review the original Sovol SV01, but from what I’ve read online, it was a pretty good 3D printer.

Sovol SV-01 Adding Genuine E3D V6 Hot End to Sovol SV-01

This one is a simple magnet with a printing surface on top, similar to what you would get with an old Ender 3. The power supply installed on the Sovol SV01 Pro is made from Creality and it’s a 24V 350W unit, similar to what you get with other Creality machines.It is ordinary for PC stickers to appear as traces of use and whitening (filaments remaining) after using them many times. Upgrade Sovol SV03 Firmware (Laser Engraving) Upgrade Sovol SV02 Firmware (Laser Engraving) Z Stop Spacer STL for Sovol Resin Flexible Plate Anycubic Mono 2. you can look that video about clog issue to disassemble the hot end parts and clean it, then assemble again, remember to tighten the nozzle and be careful, do not be burned in the process of removing the nozzle. Please check if the cable for display were connected correctly, the printers made before Sep, they are not labled. The unboxing procedure was uneventful which is what we want when we’re opening up our printer for the first time.